Year:
2007 Candy Apple Red
Performance Mods:
I am the 3rd owner of my bike. When it was November 21, 2010, it only had the the PC3, DB windscreen, and FE. I have put over 5000 miles on it this season as of now. I am a college student and am modding it on a budget (very hard to do :thumbdown). Since I was young I have always wanted a motorcycle. It was my daily commuter over the summer and I plan on tracking it in the future. This is my first bike and first season of riding. She is my pride and joy. Thanks for looking.
I just want to catalog my build to see a before and after. This is as it sits at home under the tarp. This weekend I will be stripping her down to winterize her. This will be a very slow build until I am out of college.
At Putnamville Road Course with my buddy's R1. There wasn't much done at that point I believe.
More up to date pictures
2007 Candy Apple Red
Performance Mods:
- Pipercross Air Filter
- Agg Smog Block-Off Plates
- PC3
- Radiator Guard made by bryan j
- NGK Iridium Spark Plugs
- Driven 520 Sprockets (15/47)
- EK 520 MVXZ Gold Chain
- SpeedCell 8 cell battery
- Stahlbus Drain Valve Kit with Race Cap
- ECU Flash by OhioYJ
- Samco Black Hoses with Samco Clamps
- Graves Works 2.0 Bar Radiator Cap
- Motion Pro Rev2 Variable Rate Throttle
- EBC Double-H Sintered Brake Pads
- Fren Tubo Type 4 Carbon Fiber Brake Lines
- Stahlbus Brake Bleeding System with Gold Caps
- Lightened Rear Rotor
- SBK reservoir kit
- Motul 300V 10w40 synthetic oil
- K&N 204 oil filter
- Motul RBF 600 Racing Brake Fluid
- Distilled water and Water Wetter
- Vortex Rearsets
- Renthal Clip-Ons
- Kevlar Renthal Grips
- Corbin Seat
- Woodcraft Shark Fin
- Woodcraft Swingarm Spools
- Shogun No-Cut Frame Sliders (Powder coated Hex Screws for cover)
- Driven Axle Block Sliders
- Woodcraft Ignition Cover with Black Slider
- Woodcraft Stator Cover with Black Slider
- GB Racing Clutch Cover
- ETI Fuel Cell Sliders
- Graves Motorsports Brake Lever / Hand Guard
- Motodynamic Tinted Integrated Tail Light
- Custom Led's Flasher Relay
- Removed passenger pegs
- Candy Red Passenger Peg Plugs
- GYTR Candy Red Seat Cowl
- 3rd Eye Mod
- SKUR Carbon Fiber Gauge Cover
- SKUR Carbon Fiber Tripple Tree Cover
- SKUR Carbon Fiber Tank Protector
- Crown Moto USA Tank Side Panels
- Crown Moto USA Air Duct Covers
- Carbon Fiber Swingarm Heel Covers by topherchris
- Carbon Fiber Rear Hugger by topherchris
- Carbon Fiber Exhaust Cover
- 3M Di-Noc Gloss Black Carbon Fiber Vinyl on Mid-Fairings
- R6-Forum Sock
- Blue Yamaha Racing key chain
- Unknown make DB windscreen
- Unknown make FE
- StompGrip
- Tinted Proton Flusmounts
- Decals by NJG Designs
- Vortex V3 Gas Cap
- Black Driven Sprocket Nuts
- Bridgeport 90* Angled Valve Stems
- Probolt Gold Oil Filler Cap
- Frame Plugs
- Shermoto Racing Brake and Clutch Lever
- JDA Customs Slotted Front Sprocket Cover
I am the 3rd owner of my bike. When it was November 21, 2010, it only had the the PC3, DB windscreen, and FE. I have put over 5000 miles on it this season as of now. I am a college student and am modding it on a budget (very hard to do :thumbdown). Since I was young I have always wanted a motorcycle. It was my daily commuter over the summer and I plan on tracking it in the future. This is my first bike and first season of riding. She is my pride and joy. Thanks for looking.
I just want to catalog my build to see a before and after. This is as it sits at home under the tarp. This weekend I will be stripping her down to winterize her. This will be a very slow build until I am out of college.
At Putnamville Road Course with my buddy's R1. There wasn't much done at that point I believe.
More up to date pictures