99-02 guys, post your carb settings/mods/elevation - Page 24 - Yamaha R6 Forum: YZF-R6 Forums
 
LinkBack Thread Tools Display Modes
post #231 of 285 (permalink) Old 07-29-2012, 10:35 AM
I eat my R6
 
Join Date: Mar 2006
Posts: 154
Re: 99-02 guys, post your carb settings/mods/elevation

thats true I was scared the first time now it should be easy. Did you plug off the carb coolant lines? I was thinking of doing that. Do you clean around the carbs before you remove them? just wondering
yzfr6chris is offline  
Sponsored Links
Advertisement
 
post #232 of 285 (permalink) Old 12-02-2012, 11:57 AM
I eat my R6
 
o2r6rider's Avatar
 
Join Date: Jul 2011
Location: South Georgia
Posts: 57
Bike: '02 R6
Here's what I've got: 02 r6
OEM air filter
FactoryPro spec custom V stax
Two Bros slip on (chopped)
Dyno Jet stage 1 kit, I think... (needles have 6 slots)
Clips on 3rd slot. 2 washers on top
Mains jets: 142's on 1 and 2
140's on 2 and 3
Pilots are 35's (WTF? Non Cali model???)
Mix screws are 2.75 turns out
200ft above sea level

I just cleaned carbs and it runs good and smooth through the whole RPM range with these new settings. Put a new set of plugs in too. I want to get some #40 pilots if it will make it run even better but I have no complaints as of now.
I have this adjustable timing advancer I want to install but need a second opinion on the way it should be set. I think I need to turn the outside piece clockwise to get the advance 3 degrees. The way it's set in the pic I believe to be advanced. Please correct me if I'm wrong. Thanks
Attached Thumbnails
Click image for larger version

Name:	ImageUploadedByMotorcycle1354477644.512289.jpg
Views:	17
Size:	18.8 KB
ID:	87059  
o2r6rider is offline  
post #233 of 285 (permalink) Old 12-02-2012, 02:39 PM
I eat my R6
 
bgballin26's Avatar
 
Join Date: Dec 2011
Location: Stillwater, Ok
Posts: 229
Bike: 1999 R6
Re: 99-02 guys, post your carb settings/mods/elevation

advancer won't do you any good, you should probably just sell it to me..

How is your idle? I still have a bouncy idle on mine and can't figure it out.

99 r6 ~ Factory Pro Jet kit with slight changes, OEM filter, TSR Frame Sliders, Dan-Moto Carbon Fiber GP exhaust, Renthal grips, JPR levers, pro tek bar ends, motion pro cables, Michelin Power 2ct tires, RK 520 conversion -1/stock rear, headlight signal conversion using 2003 r1 sockets, Luckybike.com flushmounts used as running lights, Puig double bubble windscreen
bgballin26 is offline  
post #234 of 285 (permalink) Old 12-02-2012, 03:03 PM
Big ol pile of them bones
 
Shush319's Avatar
 
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,566
Bike: listed in sig
Re: 99-02 guys, post your carb settings/mods/elevation

Quote:
Originally Posted by o2r6rider View Post
Here's what I've got: 02 r6
OEM air filter
FactoryPro spec custom V stax
Two Bros slip on (chopped)
Dyno Jet stage 1 kit, I think... (needles have 6 slots)
Clips on 3rd slot. 2 washers on top
Mains jets: 142's on 1 and 2
140's on 2 and 3
Pilots are 35's (WTF? Non Cali model???)
Mix screws are 2.75 turns out
200ft above sea level

I just cleaned carbs and it runs good and smooth through the whole RPM range with these new settings. Put a new set of plugs in too. I want to get some #40 pilots if it will make it run even better but I have no complaints as of now.
I have this adjustable timing advancer I want to install but need a second opinion on the way it should be set. I think I need to turn the outside piece clockwise to get the advance 3 degrees. The way it's set in the pic I believe to be advanced. Please correct me if I'm wrong. Thanks
If I had to guess, the big line in the middle is stock and you can go either +2 or -2 with the marks. I got lucky and scored a +4 Factory Pro awhile ago and what a difference that thing made. Best $50 bolt on I've bought for this thing.



CCS Racer #379

Bikez:
01' Champions Limited R6 (retiring from racing)
88' GSXR 750 (recently restored)
02' R1 (sold)
07' R6r (race project)
04' Zuma 50cc (have to get around in the pits)
01' XR70R (sold)
??' 50cc air cooled pocket bike (dangerous!)
99' CR125R (sold)
Shush319 is offline  
post #235 of 285 (permalink) Old 12-02-2012, 03:38 PM
I eat my R6
 
o2r6rider's Avatar
 
Join Date: Jul 2011
Location: South Georgia
Posts: 57
Bike: '02 R6
advancer won't do you any good, you should probably just sell it to me..<br />
<br />
How is your idle? I still have a bouncy idle on mine and can't figure it out.

Yea it's not for sale and it idles smooth. But when I rev it and let go it hangs around 3k for a couple of seconds before slowly dropping to idle..


Back on my advancer, there's only 2 marks for advance or retard but it will slide over to where a 3rd mark should be. Are the marks to the left of the big "stock" mark for advance or retard?
o2r6rider is offline  
post #236 of 285 (permalink) Old 12-02-2012, 05:27 PM
Big ol pile of them bones
 
Shush319's Avatar
 
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,566
Bike: listed in sig
Re: 99-02 guys, post your carb settings/mods/elevation

I have no idea which way is advance. I have to change my timing cover with a Woodcraft one some time this week. If I can find my factory advancer, I'll hold it up to the FP one and I can tell from there which way is advance. Hopefully I can find the old one.

Hanging up on the idle means it is lean, try 3-3.5 turns out on the screws.

DJ is the only jet kit with jets that small and 6 clip positions. I've heard it is all but useless on these bikes. Ivans or Factory Pro is what everyone has used for the most part since these bikes were made.



CCS Racer #379

Bikez:
01' Champions Limited R6 (retiring from racing)
88' GSXR 750 (recently restored)
02' R1 (sold)
07' R6r (race project)
04' Zuma 50cc (have to get around in the pits)
01' XR70R (sold)
??' 50cc air cooled pocket bike (dangerous!)
99' CR125R (sold)

Last edited by Shush319; 12-02-2012 at 05:57 PM.
Shush319 is offline  
post #237 of 285 (permalink) Old 12-11-2012, 08:00 AM
Just made this great wheelie.. did you see it?!
 
Join Date: Jan 2011
Posts: 47
Re: 99-02 guys, post your carb settings/mods/elevation

Kilburn is offline  
post #238 of 285 (permalink) Old 12-11-2012, 08:02 AM
Just made this great wheelie.. did you see it?!
 
Join Date: Jan 2011
Posts: 47
Re: 99-02 guys, post your carb settings/mods/elevation

if any one wants to fill in the rpms to match this diagram feel free it might help anyone having problems.
Kilburn is offline  
post #239 of 285 (permalink) Old 12-11-2012, 08:26 AM
Go Fast or Go Home
 
Join Date: Jun 2012
Location: Waterloo, IA
Posts: 512
Bike: 2000 Yamaha R6
Re: 99-02 guys, post your carb settings/mods/elevation

Ok so i have never messed with carbs... i work on fuel injected cars all day as im a auto tech. :P so i figured id give jetting my carbs a shot. I have no idea what my elevation is, havent searched it yet. i live in waterloo IA and i am looking to either just buy seperate jets or buy a factory pro kit. What do you guys recommend? And also if i dont get the kit do i just shim the needles? Any help would be appreciated!!! Thanks

Bryant

2000 Yamaha R6 17,xxx miles. Carbon fiber pieces. DanMoto Carbon GT exhaust. 6k HIDS. Integrated tail.
BBudensiek is offline  
post #240 of 285 (permalink) Old 12-11-2012, 09:35 AM
I eat my R6
 
o2r6rider's Avatar
 
Join Date: Jul 2011
Location: South Georgia
Posts: 57
Bike: '02 R6
Ok , since I have adjustable needles could I just copy your jet sizes and be better than the DJ setup? We have about the same engine mods. Or are the FP needles different than the DJ other than the notches?
o2r6rider is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Yamaha R6 Forum: YZF-R6 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
quick question for you guys.... keepituponone General Discussions 10 07-23-2010 08:12 AM
Did Someone Post This Guys Cl Add On Here Before??? Ryan_06_r6_raven General Discussions 8 07-29-2009 02:07 PM
What do you guys think? -iceman- Exhaust and fuel delivery 30 09-03-2006 05:16 PM
hi guys can all 05 raven owner post your pics? saleman Appearance and Exterior Mods 9 05-06-2006 10:47 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome