» Site Navigation
»
»
»» Motorcycle Forums
#1
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
02 r6 custom jet size
154's 1&4 main 40's slow . 148"s 2&3 35's slow stock pilot screws . 1 shim on needle valves. i am at sea level calif. i also have a cut off exhaust. runs super fast in mid range and full range, im just having a problem with idle ,carbs kind of chug. any suggestion, tps clean and snappy response on throttle. tell me your jet sizes.
Sponsored Links
Advertisement
#2
Big ol pile of them bones
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,263
Bike: 01' CLE R6, 88' GSXR 750
Re: 02 r6 custom jet size
Where are the pilot screws set? 2 turns out, 3, ect...
Loads of info on 1st gen settings here:
http://www.r6-forum.com/forums/showt...+carb+settings
Last edited by Shush319; 11-16-2012 at 06:11 PM .
#3
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
Re: 02 r6 custom jet size
i believe 3.25 on1&4 and 3 on 2&3
#4
Big ol pile of them bones
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,263
Bike: 01' CLE R6, 88' GSXR 750
Re: 02 r6 custom jet size
Quote:
Originally Posted by
chaka433
i believe 3.25 on1&4 and 3 on 2&3
They should all be the same. When was the last time they were sync'ed? Out of sync will make it lope too.
Last edited by Shush319; 11-16-2012 at 06:28 PM .
#5
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
Re: 02 r6 custom jet size
i have my own sync vacuum type they are all pretty close, no loop, only bog at take off.
#6
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
Re: 02 r6 custom jet size
the only thing im thinking is the # 2 carb pilot screw turns a lot easier than the rest, very loose.
#7
Big ol pile of them bones
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,263
Bike: 01' CLE R6, 88' GSXR 750
Re: 02 r6 custom jet size
Spring or O ring missing?
#8
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
Re: 02 r6 custom jet size
spring is there o-ring dont know.
#9
I eat my R6
Join Date: Nov 2011
Location: haceinda heights ca.
Posts: 108
Bike: 02 r6
Re: 02 r6 custom jet size
do they have different sizes of screw pilots?
#10
Big ol pile of them bones
Join Date: Jun 2010
Location: Daytona Beach, FL
Posts: 1,263
Bike: 01' CLE R6, 88' GSXR 750
Re: 02 r6 custom jet size
Quote:
Originally Posted by
chaka433
do they have different sizes of screw pilots?
No, screws are all the same. Pilots jets too. I never got mine super smooth until I went with next size up pilot jets.
Sponsored Links Advertisement
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes
Linear Mode
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
Linear Mode
