Any 06+ R6r stubby exhaust for 03-05 R6 or R6s

[fleixius]

Originally Posted by ATL

Simple question:

If you have no immediate plans to get an ECU/reflash, PowerCommander or Juicebox, and had the 06+ R6 stubby exhaust can for free, would you remove your stock exhaust and pay to have someone install/correctly fashion the 06+ can on there?

Or would you hold out on installing it until you purchased a PC (or other fuel remap)?
-Chris

I originally did my swap with no intention of buying a PC. So yeah, just do it.

[ATL]

Originally Posted by fleixius

I originally did my swap with no intention of buying a PC. So yeah, just do it.

Did you cut off the valve or just leave it fixed in the open position?
-Chris

[fleixius]

I didnt have an EXUP, but most take them off.

[gerrard06]

Originally Posted by 03r6special

i have the GYTR shorty on my 2003 r6, its really loud... i like it though. only drawback is that it is kind of high pitch. not as deep as i would like. but looks way better than before. it wasnt that hard, it just took a couple runs to the autopart store, and couple hours. takes a bit of fab work though.

was it hard to install the gytr? what did u do to make it fit?

[blackmer826]

alright so this is my definite mod to start off the summer. I am not sure what brand slip on I am going with but have a couple newbie questions. After reading all 16 pages.....I have a 08 R6s. What year/model do I order the stubby exhaust for? Once I get the exhaust, Do i have to trim the exhaust itself or my header, or is it already at a length that will work? or is it personal preference as to the length?

Any issues about doing this with a 08 R6S that I need to know about?

THanks

[toysareforboys]

Originally Posted by blackmer826

What year/model do I order the stubby exhaust for?

You order the exhaust for any 2003 to 2005 R6 or 2006 to 2009 R6S. Competition Werks, Riot HR1, etc. etc.

Originally Posted by blackmer826

Once I get the exhaust, Do i have to trim the exhaust itself or my header, or is it already at a length that will work? or is it personal preference as to the length?

When you get it you don't have to trim anything, it'll hook right up, mount perfect, etc.

Originally Posted by blackmer826

Any issues about doing this with a 08 R6S that I need to know about?

Because any slip-on removes the catalytic converter on your R6S it's a good idea to pickup a PCV so that you can load in a proper fuel map so your bike won't run scary lean and suck donkey balls down low.

-Jamie M.

[ridick_bowen]

I got a can off a CBR 250. Fit perfectly. Clamped it down with a u bolt.

Done! You can close this thread meow.

[blackmer826]

Originally Posted by toysareforboys

You order the exhaust for any 2003 to 2005 R6 or 2006 to 2009 R6S. Competition Werks, Riot HR1, etc. etc.

When you get it you don't have to trim anything, it'll hook right up, mount perfect, etc.

Because any slip-on removes the catalytic converter on your R6S it's a good idea to pickup a PCV so that you can load in a proper fuel map so your bike won't run scary lean and suck donkey balls down low.

-Jamie M.

I already have a D &D slip on which was on it when I bought it. As far as I know there is no Power Commander....seems to run good to me but would like to get a power commander this summer. What about an 06-10 r6 exhaust? would that mount up good or is it different. I think I am between the HR1 and the Olson as of now....but I am still not sure

[blackmer826]

what about two brothers? I cannot find any shorty two bros anywhere that would fit.

Also anyone who has a GYTR shorty how did it go? saw a lot of posts throughout discussing issues with have to directly welding it to the headers because the two pipes were the same diameter.

[blackmer826]

just found this Two Bros...would it work?????

http://store.58cycle.com/Two_Brother...%20r6%2003.htm

sorry for the questions but this is going to be my first motorcycle mod...usually do snowmobiles or wheelers.